Q&A / 

Brick Water Repellents

Brick water repellents

Brick water repellents look like this just after applying. This shine goes away completely once the silane/siloxane water repellent dries.

"These houses and commercial buildings often were constructed using two or three layers of brick or block behind the face brick you'd see on the outside of the wall. The brick in each layer was different."

Brick Water Repellent Checklist

DEAR TIM: I have a problem with my brick veneer house. It develops leaks during wind-driven rains. I can't seem to locate the source of the leaks. I purchased a brick sealer to solve my problem.

I saw water repellents at the store, but the salesperson said they don't work as well. What do you think? B. N.

DEAR B. N.: Slow down! Do you still have the receipt for the sealer? You may need it.

The sealer you purchased may actually harm your brick house. A water repellent may be a better choice.

Are Brick Leaks Normal?

The leaks you're experiencing are normal. Brick walls leak water and are not waterproof. 

Unfortunately, many homeowners think brick walls are waterproof.

Can Brick Absorb Water?

Bricks and mortar have a great capacity to absorb water. Both contain tiny passageways that actually suck water into the wall. Water can also enter through tiny cracks between the bricks and mortar.

You can build a brick wall that does not transfer water to the inside of a home. The way to do this was discovered hundreds of years ago.

CLICK HERE to get FREE & FAST BIDS from local painters that can apply the special water repellents.

Did Old Brick Buildings Leak?

Old brick buildings did leak water, but the builders knew how to construct them so the water didn't damage the interior of the building.

Water leakage into older homes is rarely noticeable. I'm talking about old brick buildings built before 1900.

How Were the Old Brick Buildings Constructed?

These houses and commercial buildings often were constructed using two or three layers of brick or block behind the face brick you'd see on the outside of the wall. The brick in each layer was different.

The outer brick that was exposed to the weather was fired longer and hotter in the brick kiln. This created a hard brick that had a low water absorption rate.

Were the Hidden Inner Brick Softer?

The inner, hidden, courses of brick in the wall were softer. They were not left in the kiln as long and were not as hard. They soaked up water like a sponge.

When it storms and wind blows rain against the brick wall the water drops are driven into the wall by the weight of the water and the wind pressure. Usually the water passes where the vertical mortar touches the brick.

The soft brick could absorb lots of water.

What Happens to the Water After a Storm?

When the sun appears after the storm, the water is released back into the atmosphere the same way it came into the brick. The breeze and sun pull the water out of the brick like a tow truck pulls a car out of a ditch.

What is Brick Veneer?

Brick veneer is a non-structural layer of brick on the outside of a building. It's only one wythe thick which is why it's considered a veneer.

In your case, you only have one layer of brick. Once this layer has been breached, the water finds its way into your house.

How Bad is the Water Leakage on Brick Veneer?

If you could look behind a brick wall that's being lashed by a wind-driven rainstorm, you'd see water flowing down the backside of the wall. It's one of the downsides to having only one layer of brick.

Where Does Most Water Enter Brick Veneer?

Water may enter through cracks or small holes in the mortar. Pay particular attention to the small vertical (head) joints between each brick. This is the most likely place where water is entering.

The method most modern bricklayers use to butter the one edge of a brick is to cut off the mortar from the bed joint of the brick they just laid and use this to butter the end of the same brick.

This does not fill the vertical joint completely and the bond between the mortar and brick is very narrow because the moisture has already been sucked from the mortar after it was cut off the bed joint.

Are the Vertical Head Joints Filled Solid?

Rarely are these vertical joints filled solid with mortar. When the bricklayer spreads mortar over the tops of the course of brick to lay the next course the mortar often bridges the vertical head joint below. There's no guarantee the joint fills solid with mortar.

Are Horizontal Bed Joints in Brick Solid?

The horizontal joints (bed) in your brick wall are usually filled in solid and resist water penetration. If you find small holes or cracks, repair these before applying any coating.

mortar joint

This is a closeup photo of a horizontal mortar joint between two layers of brick. Note the tiny cracks where wind-driven water can seep into the wall. (C) Copyright 2018 Tim Carter

What are the Types of Brick Coatings?

There are two categories of clear brick coatings:

  • film-forming sealants
  • penetrating water repellents

Film forming sealants create a continuous barrier on the surface of the brick and mortar. They should be avoided if your brick experiences cold weather.

They block the tiny passageways in the brick and mortar. Not only will they stop water from getting into the brick, but they also stop water from getting out. These compounds frequently contain acrylics, mineral waxes (paraffin), urethanes, and silicone resins.

CLICK HERE to get FREE & FAST BIDS from local painters that can apply the special water repellents.

How Do Brick Sealer Water Repellents Work?

Brick sealer water repellents work in a different way. These products are designed to penetrate deeply into the brick and mortar. Some can reach as far as 3/8 inch past the surface of the brick.

They coat the insides of the tiny passageways in the brick and mortar. However, the passageways remain open allowing the brick and mortar to breathe. These water repellent contain silanes, siloxanes, or a blend of these chemicals.

What is the Best Brick Sealer?

You want a silane-siloxane water repellent brick sealer that's soaks into the brick and mortar. CLICK HERE to get a great one.

silane - siloxane water repellent

This is a magnificent silane - siloxane water repellent that soaks into concrete. CLICK THIS IMAGE NOW TO ORDER IT.

Film forming sealants can cloud and haze over. They can contribute to brick spalling (flaking) in colder climates. Water repellents rarely discolor brick.

Because they soak into the brick and mortar, sunlight has a tough time breaking them down. Check the label on your product to see what chemicals it contains. If it's a film-forming sealant, think long and hard before applying it to your brick.

What is the Best Way to Apply a Brick Sealer?

The best way to apply a brick sealer is with a helper and a backpack leaf blower.

Read the label on the water repellent as they often say once they cure you can't put on a second coat. Some can cure in as little as 15 or 20 minutes.

brick sealer

The brick sealer has been applied on the left side of the wall. You can clearly see the wet edge. Once the water repellent is applied and it dries, the brick look just like they did before you started.

How Many Coats of Brick Sealer Should be Applied?

Many of the products recommend two coats of repellent so you can't get too far ahead of yourself. If the first coat dries, or cures, it will not allow the second coat to penetrate into the mortar joint.

Why Should I Use a Backpack Leaf Blower?

You use the backpack leaf blower to simulate what a fierce storm does. The wind pressure forces rain into the brick. Allow the leaf blower to drive the silane-siloxane water repellent deep into the brick wall. As you spray, your helper blows the repellent into the wall right behind you.

CLICK HERE to get FREE & FAST BIDS from local painters that can apply the special water repellents.

Column 095

Summary
Brick Water Repellents and Brick Sealers Are Important
Article Name
Brick Water Repellents and Brick Sealers Are Important
Description
Brick water repellents and brick sealers help keep your home dry. You need a penetrating product. Use a backpack leaf blower when applying the sealer.
Author
Publisher Name
AsktheBuilder.com
Publisher Logo
SPONSORS / 

26 Responses to Brick Water Repellents

Leave a Reply

You have to agree to the comment policy.