Q&A / 

How to Repair a Chimney

Quick Column Summary:

  • Chimney repair for the ages
  • Protect your chimney with a crown
  • Chimney liners
  • Prevent cracks with wire mesh

DEAR TIM: My chimney is constructed with concrete block and has a thin stucco coating. I know the top of the chimney is not right and some of the blocks are falling apart. There are also tiny hairline cracks all over the chimney that don’t seem to be serious. What would you do if this were your chimney and you wanted to make repairs that would last decades? What’s the most important thing to tackle now if I don’t have enough money to repair the entire chimney? John L., Newton, NJ

DEAR JOHN: Your photo is excellent and allows me to give you some solid advice long distance. I can clearly see the deteriorating concrete block at the top of the chimney and know exactly why the damage is happening. The good news is you’ll be able to restore this chimney and extend it’s service life for decades.

Let’s start the discussion with an overview of chimneys and why those built by some masons are doomed from the start. It’s important to think of a chimney as it’s own house or a structure in and of itself.

Water is very destructive to most building products, even strong masonry or solid rock. If you add freezing temperatures to the mix, the damage caused by water happens much faster. You live where winter temperatures do drop below 32 F, so it’s mission critical for your chimney to shed water.

This chimney has some cosmetic cracking and an inferior crown. It can be repaired properly and will last for decades if done right. Photo Credit: John Loughran

This chimney has some cosmetic cracking and an inferior crown. It can be repaired properly and will last for decades if done right. Photo Credit: John Loughran

Can you imagine how silly it would be to build a house and not have a roof on it? Everything inside the house would get ruined in a hurry. Chimneys are no different. They need roofs on top of them to keep water from soaking into the inside of the masonry. If you only have so much money to spend, put a proper roof on the chimney then save up to do the other repairs.

The roof of a chimney is called a crown. Chimney crowns can be made from solid slabs of stone, they can be poured concrete in place and they can even be metal. No matter what it’s made from, the chimney crown’s sole purpose is to shed water to the outside of the chimney where it can drop down to a lower roof or the ground.

Great chimney crowns have a slope to them so the water does not pond on top of the crown. The best crowns have an overhang and a drip kerf cut into the overhanging edge so all water that falls on top of the crown drips away from the side walls of the chimney.

Most masons don’t know how to construct a proper chimney crown and they rarely place a metal flashing pan under the crown. The metal flashing pan captures and diverts any water that gets past the crown. You never want any water to get into the core of your chimney. Never forget that.

You or the mason you hire needs to tear apart the top of your chimney and remove any rotten or broken block. Once you’re down to solid masonry, start to rebuild. Be aware the chimney liners may have to be extended a little higher to accommodate the new thick crown.

Keep in mind the crown should not touch the clay flue liners. A half-inch gap needs to be maintained between the crown and the liners and this gap needs to be caulked with a special urethane caulk meant for masonry control joints. This product will NOT be found at a home center. You find this special caulk at businesses that sell specialty concrete products to masons.

Be sure the new crown overhangs the sides of the chimney at least 3 inches on all sides. This may seem like a huge overhang, but from the ground it will look perfect. A quarter-inch wide by half-inch deep drip kerf needs to be located about one inch in from the outer edge of the crown on the underside of the crown.

If the crown is made from poured concrete, be sure that reinforcing steel is placed in the concrete both directions. This steel will hold the crown together. Do NOT use plain bricklayers mortar for the crown. I must be concrete or a giant slab of stone that has a pre-built slope to it.

Once the crown is complete, I would attach galvanized wire lath to the existing block and restucco over what you have. You have a rare opportunity to change the entire look of your chimney at this point by covering it with artificial stone. If you decide to do this, keep in mind the stone is much thicker than the stucco and you’ll have to make sure you get the proper 3-inch crown overhang past the outer surface of the artificial stone.

Do not allow masons to talk you into adding stucco on top of the existing stucco. The hairline cracks you see now will telegraph through the new stucco and your chimney will look horrible in no time.

The wire mesh, when attached with the proper fasteners into the solid concrete block, will prevent the existing cracks from coming through the new stucco.

All of this work should be done, if possible, when the outside temperatures range from 40 - 70 F. The best conditions to do all this work are overcast days with no wind. Sunny, hot and windy weather is the worst weather to perform masonry repairs because the water in the mortar, poured concrete and stucco leaves the materials too fast.

Column 1057

masonry-water-repellent masonry-crack-sealant

The above product links are affiliate links. I get a tiny commission if you purchase these from Amazon.

SPONSORS / 

4 Responses to How to Repair a Chimney

Leave a Reply

You have to agree to the comment policy.